|
|
Forside  Produkter EX Ventilation og ATEX Centrifugalventilatorer
Højt tryk, Lavere volumen.
|
CA
High-pressure centrifugal fans- Reinforced cast aluminium housing.
- (High performance) cast aluminium turbine.
- Max. air flow temperature: 120° C.
- Asynchronous motors, with squirrel-cage rotor.
- Standard models supplied with three-phase 230/400V, 50 Hz up to 5.5 HP, and 400/690V, 50 Hz for more powerful units; single-phase 230V, 50 Hz motors.
- Class F electrical insulation.
- IP-55 protection.
- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- On request:
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
- The fan with capacity to transport air at up to a maximum temperature of 250°C.
Mere info... |
|
CAM
High-pressure centrifugal fans- Sheet steel housing.
- Cast aluminium turbine.
- Rolled steel turbine on 752 and 880 models.
- Maximum airflow temperature: 120° C.
- Asynchronous motors, with squirrel-cage rotor.
- Standard models supplied with three-phase 230/400V, 50 Hz up to 5.5 HP, and 400/690V, 50 Hz for more powerful units.
- Class F electrical insulation.
- IP-55 protection.
- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- On request:
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
- The fan with capacity to transport air at up to a maximum temperature of 250°C.
Mere info... |
|
CAS
High-pressure centrifugal fans- Sheet steel frame.
- Cast aluminium impellers (242,248,254,260,640,645,650) and rolled sheet steel (remaining models) with high performance backward impeller.
- Aerodynamically tested to achieve maximum output with minimum sound level.
- Maximum continuous air flow temperature: 120°C.
- Asynchronous motor with squirrel cage rotor.
- Standard models supplied with three-phase 230/400V, 50 Hz up to 5.5 HP, and 400/690V, 50 Hz for more powerful units.
- Class F electrical insulation.
- IP-55 protection.
- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- Available on request:
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
- Fan capable of a maximum air flow temperature of 250°C.
- Stainless steel construction AISI304 or AISI-316.
The CAS-S variant is supplied with an incorporated silencer in the fan inlet.
The silencer has a hexagonal profile, is small and built in galvanised sheet steel and sound insulating materials. Highly variable, its special design allows for inlet airflow to be adjusted.
Mere info... |
|
CAS-S
High-pressure centrifugal fans- Sheet steel frame
- Cast aluminium impellers (242,248,254,260,640,645,650) and rolled sheet steel (remaining models) with high performance backward impeller.
- Aerodynamically tested to achieve maximum output with minimum sound level.
- Maximum continuous air flow temperature: 120°C
- Asynchronous motor with squirrel cage rotor.
- Standard models supplied with three-phase 230/400V, 50 Hz up to 5.5 HP, and 400/690V, 50 Hz for more powerful units
- Class F electrical insulation.
- IP-55 protection.
- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- Available on request:
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
- Fan capable of a maximum air flow temperature of 250°C.
- Stainless steel construction AISI304 or AISI-316.
The CAS-S variant is supplied with an incorporated silencer in the fan inlet.
The silencer has a hexagonal profile, is small and built in galvanised sheet steel and sound insulating materials. Highly variable, its special design allows for inlet airflow to be adjusted.
Mere info... |
|
CAST
High pressure centrifugal fans- Casing in rolled sheet steel.
- Sheet steel impeller with blades designed to transport powder and solid material.
- Maximum airflow temperature: 120°C.
- Asynchronous motors with squirrel-cage rotor.
- Standard models supplied with three-phase 230/400V, 50 Hz up to 5.5 HP, and 400/690V, 50 Hz for more powerful units.
- Class F insulation.
- IP 55 protection.
- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- On request:
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
Mere info... |
|
CBP
Medium-pressure centrifugal fans, backward curved impeller without feet- Rolled steel housing.
- Rolled steel (1450 and 1856) and cast aluminium (1650) backward curved impeller. Self-cleaning single inlet turbine – powder-polluted air can pass.
- Maximum airflow temperature 120° C.
- Inspection hatch.
- Motors according to IEC 34-1 (UNE 20113) VDE 0530 standard. Voltage: 230/400 V, 50 Hz.
- Class F insulation, IP-55 protection.
- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- Special for painting booths.
- On request:
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
Mere info... |
|
CBPC
Medium-pressure centrifugal fans, backward curved impeller without feet.- Rolled steel housing.
- Impeller in rolled sheet steel (1450 and 1856) and aluminium cast (1650) backward curved impeller.
- Self-cleaning single inlet turbine – powder-polluted air can pass.
- Maximum airflow temperature 120°C.
- Inspection door.
- Motors according to IEC-34-1 (UNE 20113) VDE 0530 standard. Voltage: 230/400 V, 50 Hz.
- Class F insulation, IP-55 protection.
- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- Special for painting booths.
- On request:
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
Mere info... |
|
CJMP-AL
Fans and ventilation boxes for boiler rooms.- Fans certified according to norm UNE 60-601-2000 and the requirements of natural gas boiler rooms.
- Housing and impeller in aluminium in order to avoid sparks.
- 230V, 50 Hz motor, IP-54 protection.
- Box of galvanised sheet steel and acoustic insulation.
- On request:
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
Mere info... |
|
CMA
Medium-pressure centrifugal fans (aluminium cast)- Cast aluminium housing.
- Aluminium impellers (218, 527, 528, 531, 540 and 545), polyamide impeller (324, 325 and 426) galvanised steel impeller (531-2T-3).
- Max. air flow temperature: 120° C (only 70° C in the case of polyamide impellers).
- Asynchronous motors, with squirrel-cage rotor.
- Standard models are supplied with three-phase 230/400 V, 50 Hz and single-phase 230 V, 50 Hz motor.
- Class F insulation and IP-55 protection.
- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- On request:
- Models 324, 325 & 426 can be supplied with cast aluminium impellers.
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
- The fan can be supplied to order with capacity to transport air up to a maximum temperature of 250° C.
Mere info... |
|
CMAT
Medium-pressure centrifugal fans with straight blade turbine- Cast aluminium housing.
- Cast aluminium turbine (324-531) or sheet steel turbine (540-545).
- STRAIGHT BLADES to transport dust and solid materials.
- Maximum airflow temperature: 120° C.
- Asynchronous motors, with squirrel-cage rotor.
- Standard models supplied with three-phase 230/400 V, 50 Hz.
- Class F insulation and IP-55 protection motors.
- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- On request:
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
- Special motor voltages, frequencies and protections.
- The fan with capacity to transport air up to a maximum temperature of 250° C.
Mere info... |
|
CMC
Medium-pressure centrifugal fans (sheet steel)- Sheet steel housing.
- Galvanised sheet steel turbine.
- Asynchronous motors, with squirrel-cage rotor.
Standard models supplied with three-phase 230/400 V, 50 Hz. Class F insulation and IP-55 protection.- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- Maximum airflow temperature: 120° C.
- On request:
- Fan with capacity to transport air up to a maximum temperature of 250° C.
- Stainless steel fans.
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
Mere info... |
|
CMP
Medium-pressure centrifugal fans- Sheet steel housing an all models (CMP-38-2M with cast aluminium housing).
- Galvanised sheet steel turbine.
- Asynchronous motors, with squirrel-cage rotor.
- Standard models supplied with three-phase 230/400V, 50 Hz up to 5.5 HP, and 400/690V, 50 Hz for more powerful units.
- Single-phase 230V, 50 Hz motors.
- Class F insulation and IP-55 protection, (IP-54 models 616-4T/4M and 620-4T/4M; IP-21 models CMP-38)
- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- Maximum air flow temperature:
- Models: CMP-38: 100° C.
- Rest of range: 120° C.
- On request:
- Fans with capacity to transport air up to a maximum temperature of 250° C.
- Stainless steel fans.
Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D - Other versions on request.
Mere info... |
|
CMP-AL
Fans and ventilation boxes for boiler rooms.- Fans certified according to norm UNE 60-601-2000 and the requirements of natural gas boiler rooms.
- Housing and impeller in aluminium in order to avoid sparks.
- 230V, 50 Hz motor, IP-54 protection.
- On request:
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
Mere info... |
|
CMP-X
Belt-driven medium-pressure centrifugal fans- Sheet steel housing.
- Galvanised sheet steel high-performance turbine.
- Maximum airflow temperature: 150 ° C.
- Transmission set with cast bearing support.
- Transmission set available in two versions:
A: Motor assembled on the housing.B: Motor/transmission assembled on a bedplate. - Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- On request:
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
- Fans to transport air up to a maximum temperature of 250°C.
- Straight-blade turbines except CMP-2563-X (see CMT).
Mere info... |
|
CMR
Medium-pressure centrifugal fans backward curved impeller- Rolled steel housing.
- Rolled steel turbine with high-performance backward curved blades.
- Maximum airflow temperature: 120° C.
- IEC 34-1 (UNE 20113) VDE 0530 standard motors. Voltage: 230/400 V, 50 Hz up to 5.5 HP, and 400/690V, 50 Hz for more powerful units.
- Class F insulation and IP-55 protection.
- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- On request:
- Fans with capacity to transport air up to a maximum temperature of 250° C.
- Stainless steel fans.
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D
- Other versions on request.
Mere info... |
|
CMR-X
Medium-pressure belt-driven centrifugal backward impeller fans- Rolled steel housing.
- Rolled steel turbine with high-performance backward curved blades.
- Maximum airflow temperature: 150 ° C.
- Monoblock transmission set.
- Transmission set available in two versions:
A: Motor assembled on the housing.B: Motor/transmission assembled on a bedplate. - Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- On request:
- Complete fan with motor, belts, pulleys, etc.
- Temperatures up to 250° C. Stainless steel. Inspection door. Drains, etc.
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
Mere info... |
|
CMRT/ATEX
Centrifugal fans with radial turbine and ATEX certification.- Rolled steel housing.
- Rolled steel turbine with radial vanes.
- Maximum air flow temperature: 120°C.
- Motors with ATEX certification against "DIP" IP 65T125°C dust ignition.
- 230-400V 50Hz Voltage, up to 5.5 CV and 400/690V. 50Hz for more powerful units.
- Corrosion-proof finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- ATEX Certification, category Ex II2D c II IP65 T125°C.
- On request:
Mere info... |
|
CMT
Medium-pressure centrifugal fans with straight blade turbine- Sheet steel housing.
- Straight-blade turbine suitable for transport dust and solid materials.
- Maximum airflow temperature: 120° C.
- Inlet ring with flange.
- Asynchronous motors, with squirrel-cage rotor.
- Standard models supplied with three-phase 230/400V, 50 Hz up to 5.5 HP, and 400/690V, 50 Hz for more powerful units.
- Class F electrical insulation and IP-55 protection.
- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- On request:
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
- Belt-driven fans.
Mere info... |
|
CPV
Medium-pressure centrifugal fans (anticorrosive)- Polypropylene housing and turbine.
- Max. airflow temperature: 50° C.
- Asynchronous motors, with squirrel-cage rotor.
- Standard models supplied with three-phase 230/400V, 50 Hz up to 5.5 HP, and 400/690V, 50 Hz for more powerful units.
- Class F insulation and IP-55 protection.
- 815, 1020, 1325 and 1630 models can also be supplied on request with:
- Different voltages, frequencies and protection systems.
- Category 3 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
Mere info... |
|
Typ DMV ATEX 185
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle - EX udførelse
Temperaturklasse T4
Luftmængde max. 200 m³/h
Tryk max. 640 Pa
Mere info... |
|
Typ DMV ATEX 200
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle - EX udførelse
Temperaturklasse T4
Luftmængde max. 240 m³/h
Tryk max. 740 Pa
Mere info... |
|
Typ DMV ATEX 230
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle - EX udførelse
Temperaturklasse T4
Luftmængde max. 325 m³/h
Tryk max. 940 Pa
Mere info... |
|
Typ DMV ATEX 300
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle - EX udførelse
Temperaturklasse T3
Luftmængde max. 900 m³/h
Tryk max. 1650 Pa
Mere info... |
|
Typ DMV ATEX 330
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle - EX udførelse
Temperaturklasse T3
Luftmængde max. 1100 m³/h
Tryk max. 2020 Pa
Mere info... |
|
Typ DMVL ATEX 630-1-50
Mellemtryksventilator med ventilatorhjul med bagudkrummede skovle - EX udførelse
Temperaturklasse T3
Luftmængde max. 5300 m³/h
Tryk max. 7160 Pa
Mere info... |
|
