|
|
Forside  Produkter Centrifugalventilatorer Mellemtryk
700 til 3.500 Pa statisk tryk
|
CB
Medium pressure centrifugal fans (anticorrosive)- Reinforced sheet steel housing.
- Galvanized sheet steel turbine.
- Max. airflow temperature: 120° C.
- Asynchronous motors, with squirrel-cage rotor.
- Standard models are supplied with three-phase 230/400 V, 50 Hz and single-phase 230 V, 50 Hz motor.
- Class F insulation and IP-55 protection. (IP-54 models 1428-4M and 1733-6M).
- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
Mere info... |
|
CBP
Medium-pressure centrifugal fans, backward curved impeller without feet- Rolled steel housing.
- Rolled steel (1450 and 1856) and cast aluminium (1650) backward curved impeller. Self-cleaning single inlet turbine – powder-polluted air can pass.
- Maximum airflow temperature 120° C.
- Inspection hatch.
- Motors according to IEC 34-1 (UNE 20113) VDE 0530 standard. Voltage: 230/400 V, 50 Hz.
- Class F insulation, IP-55 protection.
- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- Special for painting booths.
- On request:
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
Mere info... |
|
CBPC
Medium-pressure centrifugal fans, backward curved impeller without feet.- Rolled steel housing.
- Impeller in rolled sheet steel (1450 and 1856) and aluminium cast (1650) backward curved impeller.
- Self-cleaning single inlet turbine – powder-polluted air can pass.
- Maximum airflow temperature 120°C.
- Inspection door.
- Motors according to IEC-34-1 (UNE 20113) VDE 0530 standard. Voltage: 230/400 V, 50 Hz.
- Class F insulation, IP-55 protection.
- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- Special for painting booths.
- On request:
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
Mere info... |
|
CMA
Medium-pressure centrifugal fans (aluminium cast)- Cast aluminium housing.
- Aluminium impellers (218, 527, 528, 531, 540 and 545), polyamide impeller (324, 325 and 426) galvanised steel impeller (531-2T-3).
- Max. air flow temperature: 120° C (only 70° C in the case of polyamide impellers).
- Asynchronous motors, with squirrel-cage rotor.
- Standard models are supplied with three-phase 230/400 V, 50 Hz and single-phase 230 V, 50 Hz motor.
- Class F insulation and IP-55 protection.
- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- On request:
- Models 324, 325 & 426 can be supplied with cast aluminium impellers.
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
- The fan can be supplied to order with capacity to transport air up to a maximum temperature of 250° C.
Mere info... |
|
CMAT
Medium-pressure centrifugal fans with straight blade turbine- Cast aluminium housing.
- Cast aluminium turbine (324-531) or sheet steel turbine (540-545).
- STRAIGHT BLADES to transport dust and solid materials.
- Maximum airflow temperature: 120° C.
- Asynchronous motors, with squirrel-cage rotor.
- Standard models supplied with three-phase 230/400 V, 50 Hz.
- Class F insulation and IP-55 protection motors.
- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- On request:
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
- Special motor voltages, frequencies and protections.
- The fan with capacity to transport air up to a maximum temperature of 250° C.
Mere info... |
|
CMC
Medium-pressure centrifugal fans (sheet steel)- Sheet steel housing.
- Galvanised sheet steel turbine.
- Asynchronous motors, with squirrel-cage rotor.
Standard models supplied with three-phase 230/400 V, 50 Hz. Class F insulation and IP-55 protection.- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- Maximum airflow temperature: 120° C.
- On request:
- Fan with capacity to transport air up to a maximum temperature of 250° C.
- Stainless steel fans.
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
Mere info... |
|
CMP
Medium-pressure centrifugal fans- Sheet steel housing an all models (CMP-38-2M with cast aluminium housing).
- Galvanised sheet steel turbine.
- Asynchronous motors, with squirrel-cage rotor.
- Standard models supplied with three-phase 230/400V, 50 Hz up to 5.5 HP, and 400/690V, 50 Hz for more powerful units.
- Single-phase 230V, 50 Hz motors.
- Class F insulation and IP-55 protection, (IP-54 models 616-4T/4M and 620-4T/4M; IP-21 models CMP-38)
- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- Maximum air flow temperature:
- Models: CMP-38: 100° C.
- Rest of range: 120° C.
- On request:
- Fans with capacity to transport air up to a maximum temperature of 250° C.
- Stainless steel fans.
Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D - Other versions on request.
Mere info... |
|
CMP-X
Belt-driven medium-pressure centrifugal fans- Sheet steel housing.
- Galvanised sheet steel high-performance turbine.
- Maximum airflow temperature: 150 ° C.
- Transmission set with cast bearing support.
- Transmission set available in two versions:
A: Motor assembled on the housing.B: Motor/transmission assembled on a bedplate. - Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- On request:
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
- Fans to transport air up to a maximum temperature of 250°C.
- Straight-blade turbines except CMP-2563-X (see CMT).
Mere info... |
|
CMR
Medium-pressure centrifugal fans backward curved impeller- Rolled steel housing.
- Rolled steel turbine with high-performance backward curved blades.
- Maximum airflow temperature: 120° C.
- IEC 34-1 (UNE 20113) VDE 0530 standard motors. Voltage: 230/400 V, 50 Hz up to 5.5 HP, and 400/690V, 50 Hz for more powerful units.
- Class F insulation and IP-55 protection.
- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- On request:
- Fans with capacity to transport air up to a maximum temperature of 250° C.
- Stainless steel fans.
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D
- Other versions on request.
Mere info... |
|
CMR-PLUS
Medium-pressure backward centrifugal fans- Impeller diameter up to: 1000mm.
- Motor output power up to: 75 kWmax.
- Max air flow: 9,000m3/h.
- Max. total pressure: 400 mmcda.
- Application: aspiration of clean or lightly dust loaded air.
Mere info... |
|
CMR-X
Medium-pressure belt-driven centrifugal backward impeller fans- Rolled steel housing.
- Rolled steel turbine with high-performance backward curved blades.
- Maximum airflow temperature: 150 ° C.
- Monoblock transmission set.
- Transmission set available in two versions:
A: Motor assembled on the housing.B: Motor/transmission assembled on a bedplate. - Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- On request:
- Complete fan with motor, belts, pulleys, etc.
- Temperatures up to 250° C. Stainless steel. Inspection door. Drains, etc.
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
Mere info... |
|
|
CMR-XPLUS
Medium-pressure backward impeller belt-driven centrifugal fans- Impeller diameter up to: 1600mm.
- Motor output power up to: 200 kWmax.
- Max. airflow: 220,000m3/h.
- Max. total pressure: 400 mmcda.
- Application: aspiration of clean or lightly dust loaded air.
Mere info... |
|
CMT
Medium-pressure centrifugal fans with straight blade turbine- Sheet steel housing.
- Straight-blade turbine suitable for transport dust and solid materials.
- Maximum airflow temperature: 120° C.
- Inlet ring with flange.
- Asynchronous motors, with squirrel-cage rotor.
- Standard models supplied with three-phase 230/400V, 50 Hz up to 5.5 HP, and 400/690V, 50 Hz for more powerful units.
- Class F electrical insulation and IP-55 protection.
- Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
- On request:
- Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
- Belt-driven fans.
Mere info... |
|
CPV
Medium-pressure centrifugal fans (anticorrosive)- Polypropylene housing and turbine.
- Max. airflow temperature: 50° C.
- Asynchronous motors, with squirrel-cage rotor.
- Standard models supplied with three-phase 230/400V, 50 Hz up to 5.5 HP, and 400/690V, 50 Hz for more powerful units.
- Class F insulation and IP-55 protection.
- 815, 1020, 1325 and 1630 models can also be supplied on request with:
- Different voltages, frequencies and protection systems.
- Category 3 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.
Mere info... |
|
Syrefast ventilator VSB
Hus i sprøjtestøbt polypropylen.
Ventilatorhjul med fremadkrummede skovle, udført i polypropylen, grafitforstærket nylonnav.
Stativ i PVC
Leveres med norm motorer, 1 eller 3 faset, eller specialmotorer f.eks. regulerbar, 2-hastigheds, eksplosionssikker samt eksplosion- og tryksikker.
Speciel akselpakning beskytter motor mod syreangreb
Mere info... |
|
Typ DMV 133
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle
Luftmængde max. 150 m³/h
Tryk max. 335 Pa
Mere info... |
|
Typ DMV 185
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle
Luftmængde max. 200 m³/h
Tryk max. 640 Pa
Mere info... |
|
Typ DMV 200
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle
Luftmængde max. 240 m³/h
Tryk max. 740 Pa
Mere info... |
|
Typ DMV 230
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle
Luftmængde max. 325 m³/h
Tryk max. 940 Pa
Mere info... |
|
Typ DMV 250
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle
Luftmængde max. 420 m³/h
Tryk max. 1100 Pa
Mere info... |
|
Typ DMV 280
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle
Luftmængde max. 615 m³/h
Tryk max. 1410 Pa
Mere info... |
|
Typ DMV 300
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle
Luftmængde max. 900 m³/h
Tryk max. 1650 Pa
Mere info... |
|
Typ DMV 330
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle
Luftmængde max. 1100 m³/h
Tryk max. 2020 Pa
Mere info... |
|
Typ DMV 350
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle
Luftmængde max. 1260 m³/h
Tryk max. 2380 Pa
Mere info... |
|
Typ DMV 370-1
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle
Luftmængde max. 1700 m³/h
Tryk max. 2600 Pa
Mere info... |
|
Typ DMV 370-2
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle
Luftmængde max. 2100 m³/h
Tryk max. 2880 Pa
Mere info... |
|
Typ DMV 400
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle
Luftmængde max. 3350 m³/h
Tryk max. 3400 Pa
Mere info... |
|
Typ DMV ATEX 185
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle - EX udførelse
Temperaturklasse T4
Luftmængde max. 200 m³/h
Tryk max. 640 Pa
Mere info... |
|
Typ DMV ATEX 200
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle - EX udførelse
Temperaturklasse T4
Luftmængde max. 240 m³/h
Tryk max. 740 Pa
Mere info... |
|
Typ DMV ATEX 230
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle - EX udførelse
Temperaturklasse T4
Luftmængde max. 325 m³/h
Tryk max. 940 Pa
Mere info... |
|
Typ DMV ATEX 300
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle - EX udførelse
Temperaturklasse T3
Luftmængde max. 900 m³/h
Tryk max. 1650 Pa
Mere info... |
|
Typ DMV ATEX 330
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle - EX udførelse
Temperaturklasse T3
Luftmængde max. 1100 m³/h
Tryk max. 2020 Pa
Mere info... |
|
Typ DMV WS 133
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle
Ved 50 Hz :
Luftmængde max. 145-155 m³/h
Tryk max. 325-330 Pa
Ved 60 Hz :
Luftmængde max. 155-180 m³/h
Tryk max. 470-480 Pa
Mere info... |
|
Typ DMV WS 185
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle
Ved 50 Hz :
Luftmængde max. 200-210 m³/h
Tryk max. 640-650 Pa
Ved 60 Hz :
Luftmængde max. 220-250 m³/h
Tryk max. 890-930 Pa
Mere info... |
|
Typ DMV WS 200
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle
Ved 50 Hz :
Luftmængde max. 230-250 m³/h
Tryk max. 730-745 Pa
Ved 60 Hz :
Luftmængde max. 250-285 m³/h
Tryk max. 1000-1060 Pa
Mere info... |
|
Typ DMV WS 250
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle
Ved 50 Hz :
Luftmængde max. 425-450 m³/h
Tryk max. 1110-1160 Pa
Ved 60 Hz :
Luftmængde max. 470-525 m³/h
Tryk max. 1520-1640 Pa
Mere info... |
|
Typ DMV WS 280
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle
Ved 50 Hz :
Luftmængde max. 645-670 m³/h
Tryk max. 1430-1440 Pa
Ved 60 Hz :
Luftmængde max. 710-780 m³/h
Tryk max. 2000-2060 Pa
Mere info... |
|
Typ DMV WS 300
Mellemtryksventilator med ventilatorhjul med fremadkrummede skovle
Ved 50 Hz :
Luftmængde max. 880 m³/h
Tryk max. 1650 Pa
Ved 60 Hz :
Luftmængde max. 970 m³/h
Tryk max. 2300 Pa
Mere info... |
|
