• Galvanized steel housing and turbine.
• Sealed motors with thermal protector incorporated in winding.
• 220-240 V 50Hz single-phase. IP-54 protection.
• 220-240/380-415 V. three-phase 50 Hz. IP-22 protection.
• Class F insulation.
• PSB support bases available on request.

• Casing and turbine in rolled sheet steel.
• Closed 3 speed motors, with thermal protector incorporated in the winding.
• Single-phase 220-240V 50V motors. IP-54 Protection. Class F insulation.
• On request they can be supplied with PSB foot stand.

• Galvanized steel housing and turbine.
• Trapezoidal belt and pulley transmission.
• Free axle supported at both ends by permanently greased ball bearings.
• The bearings are in a rubber shock absorber to avoid vibration.
• The following available on request:
• Support bases (PSB).
• Motor support and belt tensing system to permit installation of a motor up to 4 HP at 1500 r/min.

• CBX series fans.
• Angular galvanized steel plate frame, electrically welded to reinforce and protect the housing.
• Highly rigid cubic structure.

• CBX series fans.
• Angular galvanized steel plate frame, electrically welded to reinforce and protect the housing.
• Rigid cubic structure.
• This construction protects the housing from belt stress.
• Rigid bridge bearings supported in the reinforced structure.

• Box made of galvanized steel, equipped with CBD fan mounted on rubber vibration dampers.
• Interior thermal and acoustic isolation made of polyethylene foam plastic M-1.
• Stuffing-box to connect fan.
• With inspection hatch.

• Ventilation box made of galvanized steel (CJBD) or in aluminium finish (CJBD/AL), equipped with CBD fan mounted on rubber vibration dampers.
• Interior thermal and acoustic insulation made of polyethylene foam plastic M-1.
• Stuffing-box to connect fan.
• With inspection hatch.

• Duct fan with backward curved impeller, manufactured in galvanised sheet steel and with acoustic insulation, its principal characteristic is the lineal air circulation between inlet and outlet.
• Outlet mounting on any side possible.
• Three-phase motors 230/400V, 50 Hz, IP-55 protection, class F.
• Standard execution with rectangular outlet.
TAC accessory in order to convert rectangular outlet to circular outlet available on request.

• Box made of galvanized steel, equipped with fan of CBX series mounted on rubber vibration dampers, Motor, V-belt, V-belt pulleys are included.
• Inside thermal and acoustic insulation made of polyethylene foam plastic M-1.
• Stuffing box to connect fan.
• With inspection hatch.
• Three-phase motor with IP-55 protection and thermal class F.

Ventilation units, equipped with reaction turbine, built in galvanised sheet and aluminium profile, prepared for the flow of air at 400°C/2h and 120°C in continuous operation. Its main characteristics are the following:

• Linear direction between intake and impulsion.
• Possibility of changing the position between intake and impulsion within the same installation.
• Hinged gate with large dimensions, used for cleaning and servicing activities.
• Its compact and rectangular design allows the movement of the fan through the gates used to access the premises. It is installed after the ducts and hoods are in place.
• 2-Speed motor, used to save energy and reduce sound levels.
• 400V 50Hz Two-speed, three-phase motors with IP-55 protection.

• Fans certified according to norm UNE 60-601-2000 and the requirements of natural gas boiler rooms.
• Housing and impeller in aluminium in order to avoid sparks.
• 230V, 50 Hz motor, IP-54 protection.
• Box of galvanised sheet steel and acoustic insulation.
• On request:
• Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.

• Fans certified according to norm UNE 60-601-2000 and the requirements of natural gas boiler rooms.
• Housing and impeller in aluminium in order to avoid sparks.
• 230V, 50 Hz motor, IP-54 protection.
• On request:
• Category 2 ATEX certification for explosive atmospheres and CE Mark Ex II 2 G/D Eex E or D.

• Reinforced casing in laminated steel. Heat resistant case in high-density mineral fibre and high thermal and acoustic insulation capacity.
• Reinforced turbine, multi-paddle type made of galvanized sheet metal.
• Maximum air transport temperature: 250°C
• Motor joined directly to turbine.
• Standardised IEC-34-1 (UNE 20113) VDE 0530 motors, Voltage 230/400V 50Hz up to 5.5HP and 400/690V. 50Hz for more powerful units.
• Class F insulation and IP-55 protection.
• Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.

• Sheet steel construction.
• Mineral fibre insulating plate.
• High performance backward curved steel impeller, high temperature paint finish.
• Maximum airflow temperature: 300°C
• Iron casting ball bearing support.
• Protected accessories (belt, pulleys, etc.) according to CE Machine Directive standards.
• 230/400 V, 50 Hz. IEC 34-1 (UNE 20113) VDE 0530 Voltage: 230/400V, 50 Hz up to 5.5 HP, and 400/690V, 50 Hz for more powerful units, class F insulation, IP 55 protection.
• Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
• On request: Heat-resistant steel construction for temperatures up to 400° C.

• Rolled steel housing.
• Rolled steel turbine with radial vanes.
• Maximum air flow temperature: 120°C.
• Motors with ATEX certification against "DIP" IP 65T125°C dust ignition.
• 230-400V 50Hz Voltage, up to 5.5 CV and 400/690V. 50Hz for more powerful units.
• Corrosion-proof finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.
• ATEX Certification, category Ex II2D c II IP65 T125°C.
• On request:
• Stainless steel fans.

• Reinforced casing in laminated steel. Heat resistant case of high-density mineral fibre and elevated capacity of thermal and acoustic insulation.
• Reinforced turbine in laminated steel with backward curved blades.
• Maximum airflow temperature: 250°C.
• Motor joined directly to turbine.
• Standard IEC-34-1 (UNE 20113) VDE 0530 motors, Voltage 230/400V 50Hz, class F insulation and IP-55 protection.
• Anticorrosive finish in polyester resin, polymerised at 180°C, after degreasing, phosphating and passivation pre-treatment.

• Manufactured in galvanised steel.
• Insulated box to avoid heat loss.
• 125 mm inlet and outlet openings, except 600 model with 160 mm diameter openings.